A rotating end with built-in ball bearings, nickel-plated brass construction and an elastomer grip define this manual holder.
Receiving range
0.1–3.2 mm, selected title range
Rotating end
Built-in ball bearings
$19.70Nov 6, 26, 05:52 PM · New YorkPrice info
This is a monthly price snapshot supplied by Rainforest, not a live quote. Product prices and availability are accurate as of the date/time indicated and are subject to change. Any price and availability information displayed on Amazon.com at the time of purchase will apply to the purchase of this product.
A dual-bearing manual holder is supplied with ten tungsten-steel bits labeled 1.6–2.5 mm and separately described chuck accessories.
Operating form
Dual-bearing manual pin-vise drill
Included bits
Ten tungsten-steel bits; stated 1.6–2.5 mm range
$20.99Nov 6, 26, 05:52 PM · New YorkPrice info
This is a monthly price snapshot supplied by Rainforest, not a live quote. Product prices and availability are accurate as of the date/time indicated and are subject to change. Any price and availability information displayed on Amazon.com at the time of purchase will apply to the purchase of this product.
A 0.6–6 mm three-jaw manual chuck, internal bit storage and five stated bit sizes provide a different format from a fine pin vise.
Chuck arrangement
Three-jaw manual chuck
Receiving range
0.6–6.0 mm, seller-stated
$9.33Nov 6, 26, 05:52 PM · New YorkPrice info
This is a monthly price snapshot supplied by Rainforest, not a live quote. Product prices and availability are accurate as of the date/time indicated and are subject to change. Any price and availability information displayed on Amazon.com at the time of purchase will apply to the purchase of this product.
Eight separately listed diameters from 2.1 to 2.9 mm are supplied as a pin-vise bit accessory, with no 2.5 mm bit listed.
Supplied diameters
2.1 /2.2 /2.3 /2.4 /2.6 /2.7 /2.8 /2.9 mm
Shank form
Straight
$27.09Nov 6, 26, 05:52 PM · New YorkPrice info
This is a monthly price snapshot supplied by Rainforest, not a live quote. Product prices and availability are accurate as of the date/time indicated and are subject to change. Any price and availability information displayed on Amazon.com at the time of purchase will apply to the purchase of this product.
Interchangeable 2 mm and 3 mm bits cut small masking pieces or plastic plate up to 0.5 mm thick.
Working operation
Cutting small circular pieces
Bit diameters
2 mm and 3 mm
$32.00Nov 6, 26, 06:17 PM · New YorkPrice info
This is a monthly price snapshot supplied by Rainforest, not a live quote. Product prices and availability are accurate as of the date/time indicated and are subject to change. Any price and availability information displayed on Amazon.com at the time of purchase will apply to the purchase of this product.
Five 1–3 mm working widths share a 3 mm shank; the maker describes a rotating chisel for a matching previously drilled hole bottom.
Maker-described operation
Rotating chisel for a matching pre-drilled hole bottom and small chisel work
Working widths
1 /1.5 /2 /2.5 /3 mm
$30.43Nov 6, 26, 06:18 PM · New YorkPrice info
This is a monthly price snapshot supplied by Rainforest, not a live quote. Product prices and availability are accurate as of the date/time indicated and are subject to change. Any price and availability information displayed on Amazon.com at the time of purchase will apply to the purchase of this product.
Choose whether you need to drill a hole, cut out a small disc or flatten the bottom of a recess. Then match the bit’s receiving shank to the holder; the working diameter and chuck range are different measurements.
Compare the actual choices
Compare the operation and receiving interface
Task or choice
References to compare
What changes the choice
Small receiving range and rotating palm end
Tamiya 74112 D-R
0.1–3.2 mm range; ball-bearing end and elastomer grip.
Dual-bearing hand-drill format
Golden Maple hand drill
Ten stated 1.6–2.5 mm bits; the separate 0.5–3.2 mm range describes receiving accessories.
Three-jaw holder with internal bit storage
QWORK WD2803
0.6–6 mm chuck; five listed bits are separate from that range.
Specific small plastic-hole sizes
GodHand GH-DB-8D
Eight exact working diameters, not every size across the range.
Flat-bottom recess finishing
GodHand GH-SB-1-3
Finish a matching pre-drilled hole bottom; a compatible holder for the stated 3 mm shank is required.
Small circular pieces
Tamiya 74122
2/3 mm discs; plastic plate up to 0.5 mm thick.
Choose the receiving holder first
Tamiya 74112 Fine Pin Vise D-R names a 0.1–3.2 mm range, a ball-bearing rotating grip end, nickel-plated brass construction and an elastomer grip. Golden Maple’s dual-bearing hand drill is another palm-and-finger-operated choice, supplied with ten stated 1.6–2.5 mm bits. Its separate 0.5–3.2 mm label belongs to the receiving accessories, not a supplied bit at every size across that range.
QWORK WD2803 uses a three-jaw chuck described for 0.6–6 mm bits and stores the supplied bits inside the tool. Its five listed working sizes are 1.5, 2, 3, 4 and 5 mm; a chuck that can receive 6 mm does not mean a 6 mm bit is supplied. Choose the holding system and actual bit inventory that suit the task.
Drilling and flat-bottom finishing are separate steps
GodHand GH-DB-8D is an eight-bit plastic-model set with specifically listed sizes: 2.1, 2.2, 2.3, 2.4, 2.6, 2.7, 2.8 and 2.9 mm. The range is not an uninterrupted set of every tenth-millimeter size; check the exact list when matching a pin or model detail.
GodHand GH-SB-1-3 Spin Blade supplies a different operation: finishing the bottom of a matching previously drilled recess, or small chisel work. Its 1, 1.5, 2, 2.5 and 3 mm working widths belong to one accessory set. The maker’s 3 mm receiving shank is the fit to check with a compatible pin vise, not evidence that every holder will fit simply because it can drill a 3 mm hole.
Choose a punch when the disc is the part you need
Tamiya 74122 has 2 mm and 3 mm interchangeable punch bits with a rotating grip. It is described for circular masking pieces or plastic plate up to 0.5 mm thick. That is a disc-cutting operation, not an alternative way to state a drill’s chuck capacity.
If the job is an outline rather than a detached piece, the circular stencil belongs in the layout stage. Keep working diameter, receiving shank and material thickness separate when planning the tools: a dimension useful for one of those checks does not establish the others.
Examples in this department
Explore these models to compare their features, included parts and intended uses.
When should I buy bits instead of another pin vise?
If the existing holder accepts the required shank and holds it correctly, you may need a working-bit selection rather than another handle. Check shank fit and exact sizes before treating the holder’s range as supplied bits.
Does a larger chuck range mean the tool drills every material?
No. QWORK names wood, resin and several plastics and excludes hard materials such as stone, metal and glass. Match the material instructions as well as the receiving diameter.
Does Spin Blade start a hole in solid plastic?
The maker describes flattening the bottom of a matching previously drilled hole, as well as small chisel work. Starting the hole is a separate suitable-drill operation; the receiving shank and working width still need to match the chosen tools.
Which tool produces a small masking disc?
The 74122 punch is described for 2 mm and 3 mm circular pieces. A drill makes a hole differently; choose the punch when the detached disc is what you need.
